, Then the market you order the bar width with no centimeters thick as the main disc and a little m

Now measure the overall height of the guitar, for example 28 cm. (Height in the pictures) multiply by 3, 4889 = 97, 69 cm. This means that harvesting a guitar should be at least 98 cm long., And preferably all 105 Measure the widest point in guitar (usually at bridge), suppose came 9 4 cm.
So 9, 4 3, 4889 = 32, 8 cm. Thus harvesting the guitar should be a minimum width of 34 cm. Now measure the waist (usually at Nekovyy sensor in normal skater guitars), height, body, neck, palms, narrowest iea place of the guitar, the distance between the pickups, etc.. claim. iea now put the picture into the cell, for example, 1 cm., and scales as many points on the photos to size.
There's even a millimeter error will lead to defeat. Make the appropriate sheet of paper and using a long ruler (preferably metal meter), put pen central axial line. This line drawing iea is the foundation, and should be straighter than a ray of sunshine. Make lines across the same calligraphic way in the following locations: 1 guitar widest point; 2 guitars narrowest iea point; 3 At the top of the body (usually the 16th fret); 4 In terms of upper thresholds, etc.. Claim. Scales sketch on paper using a pencil. So you can admire a sleek design tools and bring them in one direction or another.
Palm, I repeat, can be printed at original iea size, so as not to suffer, and maintaining a central axis pryladnaty to the picture and circle the pencil. All internal improvements guitar (sound holes and regulators and bridge) the drawings do not need to put it right on the tree will cause a blunt pencil. Finished drawings carefully cut with scissors. Putting it to a tree, a circle of his pencil.
Note: sharp pencil is needed for paper. Dumb pencil tree, no matter how hard it may be. Tree. For the basis of the neck (at the plate) should be solid wood. The thicker the base of the neck, the better, but the thinner and therefore jeweler will cover the most important element of the guitar.
For tree cover must not irritable fingers medium hard or soft wood. For body with a through iea neck, because of the neck, must be very hard (and often it is difficult) tree. Big brands iea use ash, aspen, mahogany and even pallissandr for cover.
The cheapest tree in the midst of expensive red rocks. If you are lucky enough to find on the market though that some of these rocks you lucky. I have not found anything suitable except oak. But Oak is very close to the density of ash, is widely used in hitarobuduvanni, so this should iea reassure you.
I must say that if you find rosewood (which I highly doubt) then it will cost not much less finished tool in the shop. Therefore, we will focus on oak. It's heavy, but very durable material.
Made of electro him not even require anchors (using foundations neck minimum thickness of 15-16 mm.). Since that I made oak and pad, but soon realized that even if I did vluplyu her ways, then touch it with your fingers is not very nice. Oak is always in abundance sellers door. They all stand there where they sell the rails, screeching, baseboards, trims, etc.. Claim. If you can not buy as many as 34 board width (say) centimeters, take the maximum amount you will be offered, but not less than 28 cm.
, Then the market you order the bar width with no centimeters thick as the main disc and a little more future long cut at this point. Redwood, if you're lucky, you can ask for in a yacht club, if you're lucky then these institutions are in the sea or in cities that are in the rivers. More mahogany can be artists.
Most Popular Articles Site How to decorate a yard? (855) What is the cross tattoo? (700) How to decorate Easter eggs? (627) How to make a hairstyle for prom? (584) How to make an ax in Minecraft? (568) What to draw a girl? (517) How to make a cylinder? (425) How to break a hand? (415) Which party put foil? (411)